Before the scanner arrives: seven site conditions to measure
Updated 2026-11-16
When a device feels awkward to use, the cause is usually the room, fixed the day it landed. Seven conditions — standing distance, headroom, light, floor, power, network, privacy flow — with a method and a pass criterion each.
The same device in two different rooms can produce one usable report and one unusable one. Most complaints that begin with "the device is not accurate" end with the room: backlight, an uneven floor, a standing position too close, an unstable network. These are settled the moment the device lands, and fixing them afterwards is harder than replacing hardware.
Measure seven conditions before delivery. It costs an hour and saves a relocation.
1. Standing distance and lateral clearance
Standing distance follows the supplier's recommendation, with half a step of adjustment either way. Too close and the head or feet are cropped; too far and point density drops, with edge data degrading first.
Lateral clearance must fit a guide standing slightly behind and to the side — outside the capture volume but within reach. For children and elderly subjects this position is not optional.
Floor marking. Mark the standing position with a floor sticker. It beats telling people "stand here". Replace the sticker when it wears, or the position drifts month by month.
2. Headroom and passage width: two hard limits
Headroom is not only about whether the device fits. Enclosed units such as a body-measuring booth have a stated height requirement; open body scanners still need the path from the top of the unit to ceiling lights and sprinkler heads kept clear.
Passage width decides who can come. In maternal and child, community health and rehabilitation settings, the people served may be pregnant, elderly or in a wheelchair. The passage must take a wheelchair or a pram, with margin at corners. Miss this and the device serves only part of the population — coverage is short from day one.
3. Light: direct sun and strong backlight are the usual culprits
Structured-light capture is sensitive to ambient light. Three problems, in order of frequency:
Direct sunlight. Sun falling on the standing area makes morning and afternoon behave differently. Fit a blind, or move the position out of the window line.
Ceiling backlight. A spotlight aimed toward the lens leaves gaps in the point cloud. Angle the fitting away or add a diffuser.
Floor reflection. Polished tiles or mirrored surfaces bounce light back into the lens. A matte floor mat solves the reflection and fixes the standing position at the same time.
A quick test: stand at the intended position and photograph toward the device with a phone. If the frame shows an obvious light source or strong reflection, it needs treatment. Run the repeatability test at different times of day during acceptance — light changes.
4. Floor: flatness and vibration
The device has castors or levelling feet, but they assume a reasonably flat floor. In renovated older buildings, hollow or lifted tiles show up as a larger spread between two captures of the same person standing in "about the same" place.
Vibration comes from neighbours: lift shafts, washing machines, large outdoor air-conditioning units, nearby construction. Vibration does not trigger an error. It makes data drift quietly. Move the device or add anti-vibration pads; do not try to compensate in software.
5. Power and earthing
Dedicated circuit. Do not share a power strip with high-draw equipment. Instantaneous voltage sag on a shared circuit interrupts capture, and shows up as "intermittent failure" that is hard to reproduce.
Earthing. Earth as the device requires. With poor earthing, touching metal parts can give a slight tingle and may introduce noise.
Cable routing. Run power and network cables along walls or in trunking, never across the standing area. A trip is a small matter; pulling the device over is not.
6. Network: report retrieval depends on it
Many institutions treat the network as an afterthought, and then read "the report will not open" as a software fault. QR retrieval, report write-back and remote support all depend on it.
Wired first. Use wired where possible so the device does not compete with the guest network.
Measure signal in the standing area, not in the office.
Budget for peak. During group screening dozens of people retrieve reports at once. Size for the peak, not the average.
7. Privacy and flow: usually remembered last
Sightlines. The standing area should not face a door or corridor. Add a screen where needed, with its height set against a standing adult's eye level.
Shoe-changing spot. Foot capture requires bare feet. Provide a place to sit, with an armrest in elderly settings.
One-way flow. Separate entry and exit where possible so the next person does not meet the person being captured face to face.
Screen orientation. The monitor should not face the waiting area. Report content is personal information.
Privacy flow directly affects cooperation. Poor cooperation produces poor data — it is a chain, not a separate issue.
8. Three rework scenarios that keep happening
Discovering the door is too narrow. The device fits through, the patients do not — or a wheelchair does not. Measuring passage width costs one tape measure.
Putting the position by the window. The window side is often the emptiest part of the room and gets chosen for the device. By afternoon it is backlit, and the conclusion becomes "accurate in the morning, inaccurate in the afternoon" after weeks of investigation.
A temporary network cable. A cable run for installation day is removed before go-live, and the report stops opening. Treat the network as permanent infrastructure and put it on the acceptance form.
All three share one property: visible a week earlier with eyes and a tape measure, yet usually discovered after the device is installed and the flow is running.
9. Where to spend the renovation budget
First priority: screening and blackout. A screen, a blind and a matte mat are inexpensive and solve privacy and reflection together.
Second: power and network. A dedicated circuit and wired access are infrastructure — awkward to change, worse to change late.
Third: floor levelling. Often needed in renovated buildings; costs more, but clearly affects repeatability.
Can wait: decoration and furniture. These affect appearance, not data. Get capture working and stable first.
10. Pre-delivery checklist
Tick the seven conditions a week before delivery and close any gaps first. In practice the most expensive rework involves floor and power, then network; blackout and screens are the cheapest to add.
One reminder: better site conditions improve capture stability. They do not change the inherent preconditions of measuring a living body. Values obtained outside standard conditions — close-fitting clothing, bare feet, natural stance, several seconds still, hair tied low — remain suitable only for initial screening and risk indication.
Next step
Send your site dimensions and a photo of the intended position, and the account manager will confirm whether the seven conditions hold. Cooperation runs as direct purchase or through a dealer arrangement; details are discussed directly.
Note on figures: distances and areas are nominal recommendations and must be verified on site. This article contains no pricing.
Measurement conditions and what the result covers
The accuracy figures and posture data discussed here all rest on the same measurement conditions: the person wears close-fitting clothing or shorts, is barefoot, stands naturally, stays as still as possible during the scan (about 3–5 seconds), and has hair tied back or pinned up so it does not cover the head and shoulder outline.
When these conditions are met, the data is used for preliminary screening, risk indication and follow-up comparison of posture and spinal status; when they are not met (loose clothing, movement, hair covering the outline), the result is an estimate for reference only. The device does not provide a medical diagnosis — any abnormal finding needs review at a medical institution.
Accuracy is millimetre-level (vendor nominal ±1 mm). A living body is not a calibration artefact: millimetre-level variation across three consecutive scans of the same person is normal, so read the trend from the range of several measurements rather than from a single number.
Where the data comes from
Specifications here come from the device datasheet and user manual — nothing is estimated or inferred.
Case data comes from client project records; organization names can be verified by phone. We do not use client names without authorization.
Qualification records can be looked up by certificate number in the National Medical Products Administration database.
FAQ
The room faces west and gets direct afternoon sun. Do we have to move?
Usually not. Blackout curtains, moving the standing position away from the window, or drawing the blind during capture hours will solve it. The criterion is not which way the room faces but whether direct light or strong reflection falls on the standing area. Run the repeatability test at two times of day, morning and afternoon.
What does an uneven floor actually show up as?
No error message; the data just drifts. The same person stands in roughly the same place twice and the difference is too large, yet nothing in the procedure looks wrong. Fix it with a matte mat or by levelling the floor. Do not compensate in software, because that erases real differences along with the artefact.
The network is poor. Can the unit be used offline at first?
Capture and local reports work; QR-based report retrieval, write-back and remote support are affected. In group screening dozens of people fetch reports at once, so size the bandwidth on the peak rather than the daily average.
Why is privacy part of the site requirements?
Because it directly affects data quality. A standing position facing the door, or a screen visible from the waiting area, makes people tense and move differently, which lowers cooperation and pushes the re-test rate up. A screen and a different screen angle are cheap changes and do more than repeated operator training.