Accepting a 3D scanner on delivery: twelve checks

Updated 2026-11-16

Signing on delivery day is easy; reconciling the data three months later is not. Twelve checks in three stages: before unboxing, on installation day, and across the first week.

Acceptance is the step most often skipped on delivery day. Sales is present, the engineer is present, the department head is present, and all three want the device working that afternoon — so signing becomes a formality. Three months later the data does not reconcile, report fields are missing and training never happened, and by then the device is already inside the workflow.

Acceptance is not fault-finding. It is writing down, before signature, what this device can and cannot do. The twelve checks below run in three stages: three before unboxing, six on installation day, three across the first week. Each has a method, a pass criterion and a remedy.

1. Before unboxing: verify three documents

Once the device is unboxed, powered and networked, the boundary for return becomes unclear. So check the paperwork before breaking the seal.

If the three do not agree, do not unbox. Ask the supplier for a written explanation first. Once the box is open, your negotiating position changes.

2. Installation day: measure six dimensions

Many "it feels awkward" problems are not device problems but site problems — and they are fixed the moment the device lands. Measure six dimensions and write them on the acceptance form.

Record all six on the spot. If the standing position later proves unsuitable, the fix is on the site, not the device — and this record is what makes the responsibility clear.

3. Accuracy: one person, three captures, then a changed posture

Millimetre-level is a nominal figure with preconditions: close-fitting clothing, bare feet, natural stance, still for three to five seconds, hair tied low. Acceptance is not about reproducing the factory lab; it is about reproducing results in your site, with your staff, in your process.

Note: values obtained outside standard conditions from a living subject are only suitable for initial screening and risk indication, not as measurement conclusions. Put this in the department's operating standard, not just on the acceptance form.

4. Software and report: check fields, not the interface

5. Training: the operator runs it alone

Training is not listening once, it is doing once. Have the person who will actually operate the device complete a full cycle unaided: start-up self-check, capture, report, briefing, record creation, export. The acceptor watches and does not prompt.

Three criteria: completes it alone, can explain what each item means, and knows when to recommend medical attention. The third is most often skipped and matters most for compliance — turning a number on a report into a diagnosis puts the risk on the institution, not the device.

6. The first week: watch three things

7. When something fails: three categories

Separating the three keeps the conversation from becoming mutual blame. Add a "outstanding items and rectification deadline" section to the signature page and keep a copy each — it is the only evidence three months later.

8. After acceptance: turn the form into an operating standard

Filing the acceptance form and forgetting it wastes it. At least four of its contents should become daily operating rules: standing mark, capture conditions, re-test method, exception handling.

Four sentences on the wall get followed more often than a thick manual. Whether a device is used well often comes down to whether these few sentences are visible.

Next step

If you want the twelve checks adapted to your setting, send your institution type and the models under consideration. Cooperation runs as direct purchase or through a dealer arrangement; details are discussed directly.

Submit an inquiry · How to verify a Class II certificate

Note on figures: nominal accuracy is the manufacturer's claim and only holds under the stated conditions. Acceptance methods and criteria are implementation recommendations. This article contains no pricing.

Measurement conditions and what the result covers

The accuracy figures and posture data discussed here all rest on the same measurement conditions: the person wears close-fitting clothing or shorts, is barefoot, stands naturally, stays as still as possible during the scan (about 3–5 seconds), and has hair tied back or pinned up so it does not cover the head and shoulder outline.

When these conditions are met, the data is used for preliminary screening, risk indication and follow-up comparison of posture and spinal status; when they are not met (loose clothing, movement, hair covering the outline), the result is an estimate for reference only. The device does not provide a medical diagnosis — any abnormal finding needs review at a medical institution.

Accuracy is millimetre-level (vendor nominal ±1 mm). A living body is not a calibration artefact: millimetre-level variation across three consecutive scans of the same person is normal, so read the trend from the range of several measurements rather than from a single number.

Where the data comes from

Specifications here come from the device datasheet and user manual — nothing is estimated or inferred.

Case data comes from client project records; organization names can be verified by phone. We do not use client names without authorization.

Qualification records can be looked up by certificate number in the National Medical Products Administration database.

FAQ

What is most often missed at acceptance?
Whether report fields can be exported. Most people check that a report can be produced, not that the data can be taken out, and discover at the point of departmental reporting or research analysis that they have images but no structured data. Export once on acceptance day; it takes five minutes.
Is one subject enough for the accuracy check?
No. Cover at least two body types: one standard and one outside the norm, for example unusually tall or heavy. The standard subject tests repeatability; the outlier tests the boundary. Performance at the edge of the body-type range is where everyday problems actually appear.
The supplier says it works on installation day. Is a first week of observation still needed?
Yes. Working on installation day does not mean working a week later: light changes with the season, the network changes with load, and operators change with familiarity. Watch three numbers in the first week: capture failure rate, report open rate and record completeness.
What single line must appear on the acceptance form?
Outstanding issues and their correction deadline. Acceptance is almost never all green, and anything not written down becomes a dispute three months later. Keep a column on the signature page with one copy for each side; it is the only record that will hold up afterwards.

Related

Related articles

Related devices

Related scenarios

Tell us how your organization works and we will route you to the manager for your sector.

Request a quote

If this article helped, leave your organisation and contact details and we will put together how similar institutions have handled it.

Within 30 minutes of your submission, the account manager for your sector will call you

Request a quote

No prices are published on this site; configuration and commercial terms are discussed one-to-one with your account manager